Amatol was developed by the British in World War I as a way of conserving
their meager TNT supplies. It is composed of AN and TNT in varying ratios,
the most common being 80/20. It is slightly more effecient than TNT when
used in breaching charges, but since it contains AN it is somewhat hygroscopic and must be well sealed against moisture. It has a detonation velocity of 16,000 feet per second, almost twice that of straight AN. It is
very insensitive, and while this makes it safe to handle (in fact, the
blocks can be cut up with a hand saw), it can also make it harder to detonate.
To be on the safe side, a booster should be added. One way to accomplish
this is to bore a booster well into the cast block using a 3/4-inch wood
drill bit. Dissolve some of the leftover TNT in hot acetone, pour the resulting solution into a container of cold water, and stir vigorously. The TNT
will precipitate out of the liquid in its crystalline form, which is the
most sensitive type. These crystals are pressed into the booster cavity
using heavy hand pressure, leaving a hole in which to insert the detonator.
A standard No.8 blasting cap will initiate the TNT, which in turn will detonate the amatol. If properly packaged, amatol can be stored for long periods of time with no change in sensitivity, power, or stability.
As an interesting aside, amatol was used early in World War II, but a
Canadian TNT plant changed things. Though the company had never manufactured
TNT before, production was unusually high. When the inspectors went to find
out why, they found the normal manufacturing process had been reversed.
Since this "mistake" increased output to more than three times that of any
other comparably sized plant, all other TNT manufacturers adopted it. So
much TNT was produced that there was no longer any need for amatol, and it
was phased out.
Amatol production is an excellent way of stretching an explosives supply,
getting more bang for your buck, as it were. It is not as safe to make as
some other high explosives since it uses molten TNT (very shock-sensitive),
but it should present no trouble if reasonable care is exercised.
Procedure:
1) Heat a kettle containing eight parts finely powdered ammonium nitrate
to 90øC on a water bath. A flour grinder at low speed is adequate for
powdering the AN. Seal the receiving container immediately after grinding the AN, as it will absorb moisture from the air.
2) Heat a second kettle containing two parts TNT on a water bath until
the TNT is melted.
3) Pour the TNT into the first kettle containing the AN and stir until
completely mixed. The amatol will resemble wet brown sugar and have
a consistent color and texture when properly mixed.
4) Pour the amatol into block molds or charge containers while it is
still hot. Use a cover to gently press the surface for maximum density
and to remove air bubbles. It is important that the blocks are protected from dampness or other moisture. Sealing them in plasticbags is a
good method, as is wrapping them in wax paper and dipping them in wax.
Be sure to form a cap well before they are sealed.
their meager TNT supplies. It is composed of AN and TNT in varying ratios,
the most common being 80/20. It is slightly more effecient than TNT when
used in breaching charges, but since it contains AN it is somewhat hygroscopic and must be well sealed against moisture. It has a detonation velocity of 16,000 feet per second, almost twice that of straight AN. It is
very insensitive, and while this makes it safe to handle (in fact, the
blocks can be cut up with a hand saw), it can also make it harder to detonate.
To be on the safe side, a booster should be added. One way to accomplish
this is to bore a booster well into the cast block using a 3/4-inch wood
drill bit. Dissolve some of the leftover TNT in hot acetone, pour the resulting solution into a container of cold water, and stir vigorously. The TNT
will precipitate out of the liquid in its crystalline form, which is the
most sensitive type. These crystals are pressed into the booster cavity
using heavy hand pressure, leaving a hole in which to insert the detonator.
A standard No.8 blasting cap will initiate the TNT, which in turn will detonate the amatol. If properly packaged, amatol can be stored for long periods of time with no change in sensitivity, power, or stability.
As an interesting aside, amatol was used early in World War II, but a
Canadian TNT plant changed things. Though the company had never manufactured
TNT before, production was unusually high. When the inspectors went to find
out why, they found the normal manufacturing process had been reversed.
Since this "mistake" increased output to more than three times that of any
other comparably sized plant, all other TNT manufacturers adopted it. So
much TNT was produced that there was no longer any need for amatol, and it
was phased out.
Amatol production is an excellent way of stretching an explosives supply,
getting more bang for your buck, as it were. It is not as safe to make as
some other high explosives since it uses molten TNT (very shock-sensitive),
but it should present no trouble if reasonable care is exercised.
Procedure:
1) Heat a kettle containing eight parts finely powdered ammonium nitrate
to 90øC on a water bath. A flour grinder at low speed is adequate for
powdering the AN. Seal the receiving container immediately after grinding the AN, as it will absorb moisture from the air.
2) Heat a second kettle containing two parts TNT on a water bath until
the TNT is melted.
3) Pour the TNT into the first kettle containing the AN and stir until
completely mixed. The amatol will resemble wet brown sugar and have
a consistent color and texture when properly mixed.
4) Pour the amatol into block molds or charge containers while it is
still hot. Use a cover to gently press the surface for maximum density
and to remove air bubbles. It is important that the blocks are protected from dampness or other moisture. Sealing them in plasticbags is a
good method, as is wrapping them in wax paper and dipping them in wax.
Be sure to form a cap well before they are sealed.
chenlina20160611
coach outlet
celine outlet
replica watches
louis vuitton bags
fitflops sale clearance
coach outlet
air force 1
louis vuitton handbags
michael kors purses
fitflop sandals
tory burch outlet
louis vuitton handbags
cheap jordan shoes
louis vuitton outlet
hollister
louis vuitton outlet
adidas outlet
coach outlet online
louboutin shoes
ray ban sunglasses discount
ralph lauren outlet
beats solo
cheap jordan shoes
michael kors outlet
louboutin pas cher
nfl jerseys wholesale
oakley sunglasses
lebron shoes
jordan retro
mont blanc pens
hollister kids
louis vuitton outlet stores
air jordans
replica rolex watches
polo ralph lauren
longchamp bags
coach factory outlet online
christian louboutin shoes
coach factory outlet
juicy couture
as